The Gmc Envoy third brake light moulding is an often overlooked part of the vehicle that can really bring your ride’s rear end together. While you may not think about it much, that strip above the back window is the first thing other drivers see when looking at your Envoy from behind. If it’s faded, damaged, or missing completely it can really take away from the clean look you want for your SUV. The good news is fixing up that Gmc Envoy third brake light moulding isn’t too difficult or expensive.
Signs It’s Time For a New One
There are a few tell-tale signs that it’s time to replace the Gmc Envoy third brake light moulding on your truck. Fading is a big one – over time, that black plastic just loses its shine when exposed to the sun.
Cracks are another issue – whether from age or maybe a rock chip on the highway, cracks just make it look worn out. Missing clips or pieces are a no-brainer – if parts are falling off, the whole thing probably needs to come off. Water leaks inside are no good either. A fresh new Gmc Envoy third brake light moulding is an easy fix to restore that clean look up top.
Pulling Off the Old Gmc Envoy Third Brake Light Moulding
Alright, so you’ve decided it’s time for a new Gmc Envoy third brake light moulding. The good news is removal is pretty straightforward. Start by opening the back cargo door or liftgate to access the inside.
You’ll see clips all along the front edge holding it in place – just twist each clip 90 degrees to release it from the body panel. Work your way from one end to the other freeing up each clip. Once all clips are out, the old Gmc Envoy third brake light moulding should lift right off. Clean any remaining adhesive off the body before installing the new piece.
Installation Tips for the Replacement
Installing the new Gmc Envoy third brake light moulding is the reverse of removal. Start by placing it in position, lining up all the clips. Press each one into the body panel, twisting 90 degrees to lock it in. Don’t be afraid to apply some pressure – you want a tight secure fit.
Work your way along, clipping each side into place. Once all clips are installed, press along the seam to ensure good contact with the adhesive strip. Finally, open and close the liftgate a few times to test the fit. Your fresh new Gmc Envoy third brake light moulding is now installed!
Keeping Your New One Looking Great
To really get the longest life out of that new Gmc Envoy third brake light moulding, follow some simple care tips. Whenever you wash your vehicle, be sure to spray off that third brake light area too. A little lubricant spray on the clips every few months will help prevent rust and future removal issues.
UV protectant spray will also help prevent fading and keep that new look longer. Give it a once over during your regular car washes. With some basic maintenance like this, your new Gmc Envoy third brake light moulding will stay looking fresh for years to come.
Choosing the Right Gmc Envoy Third Brake Light Moulding Replacement
When it’s time for a new replacement Gmc Envoy third brake light moulding, it’s important to choose the correct part for your specific vehicle. Make sure to reference your year, make, and model to get an OEM factory style part. This ensures a perfect color match and fit.
Aftermarket can sometimes be a little off. Check reviews too – you want one that installs easy and stays put long term. Weathertech, Replace, and Husky Liners are some trusted brands to consider. With the right Gmc Envoy third brake light moulding replacement part, the install is simple as can be.
Common Gmc Envoy third Brake Light Moulding Issues to Avoid
No guide would be complete without covering a few issues people sometimes face. One is cross-threading the clips during install. Go slow and be careful – forced clips can damage the body panel. Another is trying to pry off old clips vs twisting them out – this risks breaking clips leaving remnants stuck in there.
Ensure adhesive seal is clean too before installing new part. Dust or debris could cause leaks later on. Finally, don’t forget to seal any fasteners like bolts or screws going into that roof area to prevent future rust damage. With some care, you can avoid these common Gmc Envoy third brake light moulding problems.
Final Thought
Well folks, after reading all this I’m sure you’re itching to rip that old faded Gmc Envoy third brake light moulding off and slap on a new shiny one! Just remember to take your time removing the old piece and prepping the area.
Double check you have the right replacement part before starting too. With a little patience and care, that Gmc Envoy third brake light moulding swap is a breeze. And best of all, now when you glance in your rear view or people drive up behind you, they’ll notice how fresh and clean your ride is looking once again. Enjoy showing off that new Gmc Envoy third brake light moulding!
FAQ
Will installation damage my vehicle?
As long as you take your time removing the old part and reference install instructions, installing a new Gmc Envoy third brake light moulding shouldn’t cause any damage. Go slow, be gentle, and use care when working on any vehicle body panels.
Can I fix cracks in the old part?
While some minor cracks can be filled, once the Gmc Envoy third brake light moulding gets really cracked it’s best to just replace it. Over time fills may break down again anyway. For a clean look, fresh new part is usually the way to go.
Which adhesive works best?
Stick with the adhesive that comes with the new Gmc Envoy third brake light moulding, as it’s formulated to work well on that specific material. Aftermarket adhesives sometimes don’t bond as strongly long term.
Will it affect my third brake light function?
Nope, replacing just the Gmc Envoy third brake light moulding has no impact on the actual brake light itself. As long as bulbs and wiring are good, function will remain the same.
How do I remove leftover clips?
If old clips break off, use a small flathead screwdriver or pliers to carefully pry out the remaining pieces. Go slow to avoid further damage, cleaning up the area for a smooth new install.